Welcome to your MEO Class 4 - MOTOR Test 2
Click NEXT to start your TEST
1
The main function of tie rods in the construction of large, low speed diesel engines is to
2
The arrangement used to protect overheating of the superheaters under fluctuating loads is called
3
If the tappet clearance between the rocker arm tappet and exhaust valve stem is excessive then:
4
In a coil-type auxiliary water-tube circulation boiler
5
Types of corrosion in fresh water of D/E
6
In a 2-stroke engine a ________________ separates the under piston space from the crankcase.
7
Most steam traps respond well to cleaning. But when a thermodynamic trap fails to operate after cleaning, the next course of action should be
8
What is the purpose of the inlet grid provided within the exhaust gas casing in the gas flow path, prior entry to turbocharger ?
9
In order to reduce thermal loading on the upper part of the liner and increase the effectiveness of cylinder lubrication, modern 2-stroke marine diesel engines are designed to have:
10
Which of the following can result in cracking of piston crown?
11
Which of the following factors governs the lower limit of thrust bearing clearance?
12
The boiler water alkalinity in a coil-type auxiliary boiler should be maintained at the pH recommended by the boiler manufacturer to
13
Viscosity of fuel oil used for ME was 145cst, new fuel comes whose viscosity was more than earlier, what u should do
14
Which of the bearings listed is most widely used for main and connecting rod bearings of modern diesel engines?
15
Piston rod stuffing box scraper rings butt clearances should:
16
Which of the following layers of a thin shell bearing gives it its fatigue strength?
17
Prompt correction of speed of diesel engines driving alternators, without having massive fluctuations is ensured by incorporating:
18
When preparing to light off a cold boiler equipped with a return flow fuel oil system, the recirculating valve directs the flow of oil
19
What does the NLGI number of a grease indicate?
20
When using low sulfur fuel oil for Emission Control Areas (ECA???S), ideally the TBN of the cylinder oil used should be
21
In a uniflow scavenged marine 2-stroke diesel engine, the scavenge ports in a cylinder liner are machined
22
Why does a chain stretch in service?
23
Which of the following conditions can lead to reduced power developed by a main engine?
24
Which of the following statements is false?
25
Which of the following will be required to be done in order to reduce sulphur corrosion of main Engine Components?
26
In the latest concept of Variable Geometry Turbocharging, _______angle can be varied to match the turbocharger at varying engine loads
27
Which of the following can be done to reduce the cold corrosion of Main Engine cylinder liners using high sulphur fuel oil
28
Which of the following gauges are generally used to evaluate main bearing clearances?
29
Fusible plugs are installed in fire-tube boilers to
30
The primary function of a flame safeguard system, as used on an automatically fired auxiliary boiler, is to prevent
31
For a continuous operation diesel engine, a duplex filter unit would be the best arrangement because
32
Directional intake ports in diesel engines are used to
33
Which of the following types of diagrams would give an indication of effectiveness of exhaust and scavenge processes?
34
Sudden stop of diesel engine
35
To avoid the engine running too long on critical speed during start up it is necessary to
36
When m/e is running in emergency condition which of the alarms can't be bypassed
37
Where boiler point temp high?
38
External fouling of boiler tubes can lead to:
39
When A/E stand by F.O.heater to be used for main engine
40
The fall in speed that occurs in a diesel engine equipped with governor, on increase of load is called:
41
Which of the following functions is done by a cam operating an exhaust valve?
42
The purpose of economizer is to:
43
Supercharging an existing medium speed naturally aspirated engine will
44
An auxiliary engine turbo-charger makes strange noises when the load changes. The engine parameters however are absolutely fine. An external examination of turbocharger parameters as stated in the manual also reveals nothing. Would you
45
Modern 4-stroke medium speed, marine diesel engine exhaust valve spindles are rotated by providing
46
As per regulations, within how many hours before each departure, satisfactory working of the steering gear must be checked?
47
The muffling of exhaust gas noise in 4 stroke auxiliary engines in achieved by
48
Which of the following methods is normally used to lubricate bearings in a small high-speed diesel engine?
49
Which of the following types of damages are metal seatings of a valve subject to? Choose the correct alternative.
50
Mixed lubrication consist of
